A Toshiba PLT-1005BT biopsy guide is a bracket-and-insert set that mounts on the Toshiba PLT-1005BT linear transducer and holds the biopsy needle on the path shown by the system’s guide line. Akicare supplies needle guides compatible with Toshiba (Canon) linear probes, including the PLT-1005BT, in reusable stainless-steel and sterile disposable formats. Below is what the guide is used for and how to specify the right configuration.
What the PLT-1005BT Biopsy Guide Is Used For
The PLT-1005BT is a high-frequency linear probe used on Toshiba/Canon Aplio-series systems for small parts, breast, thyroid, MSK, and vascular imaging. Those are exactly the applications where guided biopsy is common: thyroid FNA, breast core biopsy, and superficial lymph node sampling. The bracket clamps onto the probe housing; gauge-specific inserts then fix the needle channel so the needle enters the scan plane at a known angle and stays visible along its full length. Compared with freehand technique, a guide shortens needle-placement time and reduces the number of passes needed on small superficial targets.
Reusable vs Disposable Formats
| Attribute | Reusable guide | Disposable guide |
|---|---|---|
| Material | Medical-grade stainless steel bracket | Sterile single-use polymer kit |
| Needle path | Interchangeable gauge inserts on a fixed bracket | Pre-set channel supplied with the kit |
| Sterilization | Steam autoclave between cases | Supplied sterile; discard after one procedure |
| Cost profile | Higher unit price, low cost per procedure over hundreds of uses | Low unit price, recurring cost every procedure |
| Best fit | Departments running biopsies regularly | Low-volume sites or mobile services without autoclave access |
Superficial biopsies on linear probes are usually fine-needle (21G–23G) or core (14G–18G) procedures, so confirm the insert set covers both if your department performs both.
Sterilization and Reprocessing
Reusable stainless-steel brackets are designed for steam autoclaving. After each procedure, detach the guide from the transducer, clean it according to your facility protocol, and autoclave the bracket separately — the transducer itself must never be autoclaved and should be reprocessed per the probe manufacturer’s instructions. Disposable kits arrive sterile-packed and are discarded after a single use, which removes reprocessing workload but adds a per-procedure consumable cost.
Because the bracket clamps directly onto the probe housing, inspect the probe lens and housing for wear whenever you mount a guide. If you find lens delamination, cable damage, or image dropout, a probe repair For PLT-1005BT, repair pricing and turnaround depend on the fault, probe model, parts availability, and agreed test scope; request an assessment before comparing repair with replacement.
What to Confirm Before Ordering
- Exact probe model: the bracket is machined to the Toshiba PLT-1005BT housing; a guide for a similar-looking probe will not seat correctly.
- Needle gauge: confirm the insert set covers the gauges your clinicians use (commonly 14G–23G for core and fine-needle work).
- Guide-line software: verify your ultrasound system displays the biopsy guide line for this transducer so the on-screen path matches the physical channel.
- Reusable vs disposable: match the format to your case volume and reprocessing capacity, as compared in the table above.
- Documentation: request the compatibility statement and material certificates with your quotation.
Akicare lists Toshiba needle guides for related linear models such as the PLT-1204BT (TSM-049) and PLT-805AT (TSM-068); for the PLT-1005BT specifically, contact us with the probe model for the matching bracket. You can browse all biopsy needle guides or the full Toshiba probe catalog.
Request a Quote
Akicare supplies biopsy needle guides compatible with the Toshiba PLT-1005BT, alongside compatible replacement transducers and probe repair services. For PLT-1005BT, compatible or refurbished probe pricing depends on the exact model, condition, test documentation, availability, and order terms; compare a current RFQ with OEM supply. Send us the probe model and your preferred needle gauges through the contact form, and our team will return a quotation with specifications and lead time, usually within one business day.
